...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
Version 1.5.7
Release Date
Features and Improvements
Added oxycom2 script associated with the RS485 port
Enabled access to device services when full GRE tunnels are configured
Added WPA3-Personal support for the CTM-500
Dead Reckoning feature on the CTM-500.
Note that this feature is BETA in this release
GPS module FW upgrade for the CTM-500. Note that a specific FW is required for DR feature above
Bug Fixes and Changes
Fixed frequent vuereport restarts
Fixed factory reset operation with “staged” files present
Increased number of slaves supported for MODBUS Master Gateway
IPSec Config strings with white spaces are now rejected
Download CTM-500 firmware v1.5.7 here.
...
Version 1.5.6.1
Release Date
Features and Improvements
Improvements to IPSec IKEv1 proposal configuration to simplify handling of multiple AED proposals.
Bug Fixes and Changes
Fixed frequent cell disconnect issue caused by statistics gathering process.
Download CTM-500 firmware v1.5.6.1 here.
...
Version 1.5.6
Release Date
Features and Improvements
Added DHCP MAC Binding
Improved CTM-ONE LPM Power Consumption
Bug Fixes and Changes
Fixed a Validation Error on WLAN1 IP subnets
Fixed Local Serial Reports Display on GUI
Fixed required reboot to enable or disable local UDP or TCP reports
Fixed a bug causing Stale PGPS
Fixed a bug that makes IOT process stuck on fail
Download CTM-500 firmware v1.5.6 here.
...
Version 1.5.5
Release Date
Features and Improvements
Added LPM Message to Eventlog
Added support for SNMPv3
Improved Configuration Validator to Support Hardware Configuration
Added a Feature to Allow Device to Check to IOT When Device Time is 1970
Enabled STAGPS support for L26-ADR GPS Module on the CTM-500
Implemented Hosts File Management via device configuration
Implemented Feature to Restart GPS Process After Inactivity
Bug Fixes and Changes
Changed configuration validator to Only Allow Supported Keys to be sent to Cypress VUE/IOT
Fixed a Bug That Causes CELL_TOTAL_RX Values to Drop
Changed IOT Process to not Restart When Changing Configuration
Changed GUI Feedback When Changing OFIE Settings
Fixed DNAT Firewall Rules not being applied
Fixed Cached IMEI data on CTM-500
Download CTM-500 firmware v1.5.5 here.
...
Version 1.5.4
Release Date
Features and Improvements
QoS
Dual SIM Failover
Support for CTM Connect GATT Endpoint
LED flashing while booting
Calculation of GPS SQI
Bug Fixes and Changes
Improved resiliency of OTA FW Upgrades
CAN_STATUS key state not correct with CAN disabled
NET_ETH0_LINK key state not indicating Ethernet disconnected
Device not aborting LPM if ignition comes back
Setting interface metric for DHCP client interfaces
CTM-500 WIFI driver update
Automatic deletion of feature log files when disabling log in the configuration
Improper handling of DNS when switching SIM slots
Pass through static - Routing between devices on the same subnet
Spreader support updated to 1.7.1.fw - CIRUS material name fix
...
Version 1.5.3
Release Date
Features and Improvements
Added option to report packets in order
Added GATT Endpoints feature
SNMP v1 and v2
Diagnostics mode for CTM Connect
Bulk reporting to Cypress-IOT
Non password protected installer page
Added uBoot management utilities
Network diagnostics features in web GUI
Added Validator for 1.5.3 Downgrades to 1.5.X
Bug Fixes and Changes
Fixed BT startup issues on CTM-500
Fixed BT broadcast issues with GATT enabled
Removed support of the FC66EB module
Fixed Iptables rules not being applied after FW upgrade
CTM-500 showing internal antenna option for WiFi
Importing configuration causes issues with Radius authentication
Increase maximum number of supported WiFi clients for v4 hardware
Made secondary IP DHCP lease time configurable
Integrated IPSec with system logging
Beautified the installer page
Numerous improvements to Cypress-IOT job management
...
Version 1.5.1
Release Date
Jun 14, 2023
Hotfix
Fixed an issue with cypress-iot client not restarting after cell disconnects, causing IOT check-ins to stop
...
Note: Downgrades from version 1.5.0 and above are not supported
Release Date
May 23, 2023
Features and Improvements
Added encryption of secure fields, such as passwords and secrets
Added ability to reset password to factory settings from GUI
Added an option to report only the changed keys in reports
Improved the CLI options to better display configurations and hierarchy
Bug Fixes and Changes
Fixed Radius fallback timeout causing slow GUI performance issue
Fixed ISP-provided DNS not working issue
Fixed NAT rules not applying immediately with config change issue
Fixed Custom Firewall rules requiring a restart issue
Fixed corner cases with CAN and Network data not displaying correctly in GUI
Fixed network watchdog not restarting with cell config changes issue
Improved WiFi functionality on CTM-500
Improved IoT jobs management
Improved validation for WiFi passwords
Improved power management
Standardized menu labels and titles across GUI
Disabled SSH access by default for enhanced security
...
Version 1.4.2
Release Date
Features and Improvements
Added apps management
Added WLAN bridge functionality
Added ability for CAN parameters to lock onto specific ECU address
Added remote logging
Added ability to see logs in GUI
Added button to send details to IoT for troubleshooting
Added support for array config management via CLI
Added dhcpdump utility to CLI
Matched iwconfig output between WG7831 and FC21
Bug Fixes and Changes
Fixed VLAN interfaces functionality
Fixed DHCP Relay functionality
Fixed Radius SSH authentication
Fixed firewall rules ordering issues
Fixed Passthrough static mode issues
Improved custom firewall rule management
Improved Radius error management in case of wrong configuration
Removed default route option from eth0/1 settings
Fixed spreader initialization issues
Fixed the reading of AIN values over MODBUS
Fixed no hysteresis issue on general-purpose inputs
Fixed CTM-ONE Power Consumption in LPM
Fixed the inability to disable IoT check-ins
Fixed minor SNF issues
[Other] Minor bug fixes
...
Version 1.4.1
Release Date
Features and Improvements
Added configuration migration from 1.3.x FW versions to 1.4.1
Added Device ID for reporting and management
Added spreader support to FW
Added CPE monitoring
Added Ping proxy feature
Added Import/Export device configuration feature via web GUI or command line
Added QXDM logging capability
Ported RSSIMON command from Oxygen 3
Improved web GUI
Improved local web GUI session management
Improved local password management
Improved CTM-500 LED status
Improved presentation of cellular information with LTE-A and 5G radios
Added deprecated ciphers for compatibility support
Added dual WiFi radio support for CTM-ONE
Added support for Quectel RM520N-GL 5G radio
Added support for Variscite v 3.1 SoM based on ADI Ethernet Phy
...